熱穩定增韌尼龍

發布于2023-11-03 15:54:53 點擊：0

產品介紹：PA66，熱穩定，注塑級，自然色

應用領域：汽車，工具，電子電氣，工業等。

物理形態和儲存

產品以干態供貨，一般為圓柱狀顆粒，用防潮袋包裝，便于使用。標準包裝形式是二十五公斤袋裝，也可以根據協議提供其他形式的包裝。所有包裝都是密封的，應該在加工使用前才可打開。為避免干燥的材料從空氣中吸收水分，必須儲存在干燥的房間。如果取出部分材料后必須再仔細密封包裝。

產品可以無限期地保存在未破損的袋中。經驗顯示材料儲存在散裝桶三個月，吸水對加工性能沒有任何不良影響。儲存在冷藏室的，應使其達到常溫平衡，這樣顆粒不會有冷凝水。

The products are supplied in dry state, generally cylindrical pellets, packaged in moisture-proof bags for ease of use. The standard packing form is 25kg bag, and other forms of packaging can also be provided according to the agreement. All packages should be sealed and opened before processing. The products must be stored in a dry room to prevent the dry material from absorbing moisture from the air. If some materials are taken out, you must carefully seal the package.

The products can be maintained in undamaged bags. Experience shows that the materials are stored in bulk tanks for three months and water absorption has no adverse effect on process ability. The materials that are stored in a cold closet should reach room temperature equilibrium to avoid the particles with condensation.

當產品在建議的條件下加工，熔體是穩定的不會因為高分子降解產生有害的物質和氣體。如同其他熱塑性聚合物一樣， 當給予過度的熱能，如過度加熱，或者燃燒清潔，產品會降解。詳細信息 可以參考物質安全資料表。

If the product is processed under recommended conditions, the melt is stable, harmful substances and gases will not produce by degradation of high molecular weight polymer. Like other thermoplastic polymers, products degrade when given excessive heat, such as overheating, or combustion cleaning. Refer to the MSDS for details.

本資料內容基于本公司目前掌握的知識和經驗。由于存在很多因素可能影響我們產品的應用和加工，因此本公司不排除用戶進行試驗研究的必要。本資料也不保證具體應用的適應性或某些性能的可靠性。這里的任何描述，圖紙，照片，數據，大小，重量等可能不事先通知而更改，但不包括已經達成一致的合同。我們產品的使用者應確保遵守所有權及現有的法律法規。有關產品有效性，請聯系我們。

This information is based on the current knowledge and experience of the company. There are many factors that may affect the application and processing of our products, the company does not rule out the need for users to carry out experimental research. This information also does not guarantee the suitability of specific applications or the reliability of certain performances. Any descriptions, drawings, photographs, data, sizes, weights, etc. may change without prior notice, but does not include the agreed contract. Users of our products should ensure compliance with ownership and existing laws and regulations. For product availability, please contact us or our sales agent.

未著色產品的典型值在23℃以下。(Typical value of uncolored product is below 23 ℃)

1）染色料的性能可能與以上數值有不同。所有數據是在23℃、50%相對濕度的環境中存放24小時后測試所得。除熔融指數和灰分外的其他性能均使用注塑樣條進行測試。

Variations within normal tolerances are possible for various colors. All values are measured at least 24 hours storage at 23℃/50%RH. All properties, except the melt flow rates and the ash content, are measured on injection molded samples.

2）典型值是指實驗平均數據，僅用于使用時的參考，不作為產品的標準。

Only typical data for selection purposes. Property values are the average experimental data, when used only for reference, not as a product standard.

3）燃燒性能的結果僅為小規模的實驗室測試所得，不能反映災害或任何其他材料在實際火災中的燃燒情況。

Flammability results are based on small-scale laboratory tests for purposes of relative comparison and are not intended to reflect the hazards presented by this or any other material under actual fire conditions.